無關人員要遠離薄膜打孔機。薄膜打孔機需要由專業的操作人員來進行操作，在工作途中不允許沒有受過操作的人靠近，以免造成危險事故，或者影響操作人員。薄膜打孔機在運轉的時候，不可以把手和腳放在可移動的零部件上面，以免這些零部件的運動使得薄膜打孔機的運作受到影響。對于一些比較敏感的部分要注意避開。

使用完薄膜打孔機之后要進行一個深度的清洗，確保薄膜打孔機的干凈。平時也要注意多保養一下薄膜打孔機的內部零件，比如說各種電機和軸承齒輪等等。薄膜打孔機根據加工的尺寸大小，加工孔的數量，加工孔的尺寸，加工孔位置數據等制作固定夾具。把夾具和自動轉盤緊固，再控制電腦內設定好加工數據。把需加工的材料固定在自動轉盤上。

 薄膜打孔機啟動機器，機器根據電腦指令和加工數據一次性完成打孔、鉆孔、銑孔、通孔、盲孔、多孔、高低孔等加工程序。薄膜打孔機工作臺由人工控制或采用數控裝置控制，在三坐標方向移動，為了方便又準確地調整工件位置，薄膜打孔機工作臺上加工區的臺面用玻璃制成，因為不透光的金屬臺面會給檢測帶來不便，而且臺面會在工件被打穿后遭受破壞。

薄膜打孔機工作臺上方的聚焦物鏡下設有吸、吹氣裝置，以保持工作表面和聚焦物鏡的清潔。在薄膜打孔機使用前，一定要檢查沖頭及下模刀口處是否有雜物。在沖頭上部加上潤滑油，持續工作時，保持薄膜打孔機加油部位不缺油。使用時如有異響，請及時處理。薄膜打孔機必須擦干凈，否則會引起產品稀路針或緊密路等疵病。

消除薄膜打孔機內積垢，可利用斷鋼鋸條的背面來剔。如一次剔擦不清，可復剔一次，要達到潔凈為止，然后再用刷子剔出油垢塵屑。不可貪圖方便，將薄膜打孔機翻過來敲擊，以免損壞薄膜打孔機。